Durham Region Air Conditioning Repair, Service and Installation
If you're looking for help fixing your Heil furnace, look no further! Our comprehensive Heil furnace repair guide will explain common issues, provide troubleshooting tips, and show you how to read your model's error codes..
CODE: Heartbeat.
RESULT: Control has 24 VAC power.
RESULT: Control has 24 VAC power.
CODE: 2 Flashes.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
CODE: 3 Flashes.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
CODE: 4 Flashes.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
CODE: 5 Flashes.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
CODE: 6 Flashes.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
CODE: 7 Flashes.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
CODE: 8 Flashes.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
CODE: 10 Flashes.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
CODE: 1 + 2 Flashes.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
CODE: 6 + 1 Flashes.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
CODE: LED Off.
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
CODE: LED On.
RESULT: Control circuitry lockout- Auto-reset after one hour.
RESULT: Control circuitry lockout- Auto-reset after one hour.
CODE: LED SOLID.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
See What Our Customers Are Saying:
Mar 16, 2018
Greg came by to do a routine furnace checkup. He was very knowledgeable and professional, letting me know what's being checked/adjusted and giving me tips to ensure everything runs smooth. Very honest and upfront about what's working fine vs. what may need to be fixed/replaced. He didn't attempt to up sell anything that wasn't necessary. I'm glad to have finally found someone I can trust and rely on for all my HVAC needs - furnace, A/C, and hot water tank.
Mar 4, 2018
I'm very happy with the work that was done. Everyone from salesperson to the installers were friendly and professional. They were on time and cleaned up the job site after it was installed. They also answered all my follow up questions promptly. I wouldn't hesitate to work with them or recommend them again.
Feb 28, 2018
Thanks to the team at Twin Tech for a great job installing my new heat pump/ac unit. The guys were very polite and professional. When they left you would never have known they had been there except for the new Mitsubishi unit on the wall!! would highly recommend the Twin Tech team.
Feb 28, 2018
Installed professionally, no delays, no rework needed. Very reliable contractor and sales person. Also installed BBQ gas line and some duct work.
Feb 19, 2018
Greg and Grant are friendly, reliable, and knowledgeable HVAC professionals. The twins, Dave and the entire team provided efficient top quality service. Our family plns to use Twintech for all of our future HVAC needs.
Feb 10, 2018
Very impressed with this company. They show up on time , kept my place clean and after they left it looks like they were never there. Very professional team. Those people know what they doing . Their installation was on the highest standard. They are very knowledgeable especially they're worker Peter. I strongly recommend this company to everybody. After the installation I receive the call making sure I'm satisfied with their products and their job. Bravo!!!
Feb 8, 2018
Greg and his brother were referred to us by a friend. They arrived when they said they would, did an exceptional job and left the place as tidy or tidier then they found it. Their professionalism is only surpassed by their kind and friendly demeanor. Even after several calls to help me with my high tech thermostat I feel that I could always call with any concern (No one responds to my texts as quickly as Greg) and have a friendly helpful response. I found out their grandfather started the company and now as a 3rd generation company, they are doing their grandfather proud. I would highly recommend Twintech over any other hvac company out there.
Feb 7, 2018
Thanks to the guys at Twintech Heating for a great job installing a new hot water tank. They set a time and day to remove the old tank and install the new one. They were on time and had the work done quickly and cleaned up after they were finished. Excellent work and great value.
Feb 1, 2018
In November, we contacted Twintech for a quote on a high efficiency furnace plus installation. Dave, the sales representative for the company was very friendly and informative. Upon arrival at our home, he willingly showed us his company licenses, clearly explained the operation of a high efficiency furnace and answered all our questions to our satisfaction. As well, Dave was the only sales representative that we contacted that was willing to make the arrangements for an energy audit. For us, this was a big plus as we found the government rebate program somewhat confusing to navigate. The furnace was installed on the date that was arranged in an efficient and professional manner by Greg (the owner) and Peter. Both men worked diligently, throughout a long day to complete the job and upon finishing, left the job site immaculate. When a neighbour raised concerns about the furnace venting location, Greg located an alternative location and resolved the situation with diplomacy. We chose the Napoleon furnace for its excellent warrant;y on the heat exchanger and because it was made in Canada! In addition, to the furnace warranty, Twintech offered us a 5 year warranty on labour which speaks to the quality and pride this team has in their workmanship. It has been over a month now (with some of the coldest January days on record) since we have had the furnace installed. The furnace runs quietly and distributes heat more evenly throughout our 90 year old Toronto home. We can't speak highly enough of the Twintech team and are very satisfied with their workmanship and job ethics. We have no hesitation about recommending them.
Jan 31, 2018
What more could you ask for! Grant and Greg Dainty provided a professional,diligent and thorough approach to the installation of my furnace. I would highly recommend there services.