Categories
- AC Filters
- AC Repair
- Air Conditioner Maintenance
- Air Conditioner Repair
- Air Conditioners
- Air Conditioning Services
- Air Quality
- Cleaning Tips
- Cooling
- Duct System
- Ducted Air Conditioner
- Ductless Air Conditioner
- Emergency Repairs
- Energy Costs
- Expert Help
- Fans
- FAQ
- Filters
- Fireplaces
- Fun
- Furnace Installations
- Furnace Repairs
- Furnaces
- Gas Fireplaces
- Gas Line
- Gas Line Installations
- Heat Pumps
- Heating
- Heating and Cooling
- Heating Contractors
- heating system
- Heating Technicians
- Humidity
- HVAC
- HVAC Contractors
- HVAC experts
- HVAC Noises
- HVAC professionals
- HVAC Repairs
- HVAC Service
- Insulation
- Maintenance
- Natural Gas
- Pestibulum molestieenean
- Saving Money
- Water
- Water Heaters
- Work
[BACK]
Humidity issues with ducted Mitsubishi heat pump
Posted On: September 5, 2023
Hello, wondering if others have experienced difficulty maintaining comfortable humidity using a Mitsubishi hyper heat ducted system.
I think the heart of the matter is that they try to be too efficient and can maintain temp well but ignore the importance of humidity.
I have an old inefficient carrier ac downstairs which works great at keep the lower level cool and dry.
My upstairs unit is the heat pump.
I tend to use dry mode as it seems to work better than cool mode since it will try to run longer by keeping the fan speed low and the coil cold.
However, it only really significantly brings down humidity when it's first turned on.
And it does this really well initially.
It can drop eh by like 10% in an hour.
You can repeat this effect by continuing to lower the set point but then you just end up chasing uncomfortably cold temperatures to meet humidity.
If I set it at 74 it will cool until it hits 71 degrees, then shut off and kick back on when it reaches 73.
I could run a portable dehumidifier but they are loud, need to be emptied often unless you have a drain nearby, and consume lots of power.
If I could just hack this thing to run less efficient, ramp up the compressor hit a set point shut off and do it again I think It would be more comfortable.
Or come up with a way to schedule it so that the set point is at 74 then shuts off at 73, unit waits to turn back on at 75 and repeat.
Any thoughts or suggestions?
Thanks.
Question from user Ok-Swan2736 at heatpumps at reddit.
Answer:
Dry mode is 100% cooling.
It could also be that your unit is oversized.
You satisfy temp setpoint before pulling any moisture out of the air.
This is not the fault of your unit, but of your installers system selection.
Answer from user rayinreverse at heatpumps at reddit.
[BACK]
See What Our Customers Are Saying:
Apr 10, 2019
Had new furnace installed and ran into some difficulties but the contractor responded in a timely and efficient manner - after further service calls were made, a reasonable resolution was found.
Apr 8, 2019
The work was done quickly efficiently neatly and professionally. Pleased with the service, information, product, and the company.
Apr 1, 2019
Great sales member named Dave came in told us some amazing items and how they would be priced installed an all. We couldnt believe it! The next day the ac was installed, that day one employee named Greg told us that our furnace was working way to hard and was causing us to use way too much gas. So two days later they came in an installed a new furnace!
Apr 1, 2019
Installation was done quickly and professionally. The new furnace is quiet and provides even heat.
Mar 3, 2019
They removed and discarded old furnace. Installed new furnace. Installed air intake pipe, that had never been installed by builder, no charge. Replaced loose hose on floor with hard pipe and rerouted it to drain, no charge. Almost 33% cheaper then quote from Enercare, which was the company we dealt with and had insurance with for 8 years. No yearly fee for cleaning/insurance, saves 300 a year. Courteous, professional, fast, and friendly. My wife and I have been recommending them to everyone we know and meet, and will continue to do so. Thanks for everything, Twintech!!!
Mar 4, 2019
This company was great to deal with. Our furnace went down and they installed a new furnace the next day with a lot of professionalism!
Feb 22, 2019
Finally! An honest company with highly knowledgeable and informative staff. Had a furnace service and found multiply errors in our system from an amateur installer. Very fair price to correct problems and will definitely use again.
Feb 16, 2019
Had to replace the heating & a/c unit in a condo apartment dwelling. this company recommended by the property manager and president of the condo building. found their workmanship and attention to details very good and very thorough. were able to resolve small problems and situations and happy to feel the heat in my unit. it's pricey, but happy was done by a very professional service. thank you.
Feb 13, 2019
Fantastic team. Completed the job as per the specifications and in under 3 hours. Highly recommended Twintech.
Jan 30, 2019
During the summer, I previously hired TwinTech to replace my air conditioner when it failed. They did an excellent job so when I decided to proactively replace the furnace I contacted them. The furnace I had was 22 years old and showed signs of internal leakage. It still worked but rather than wait to have it fail in cold weather, I decided to purchase a higher efficiency model before it failed and take advantage of energy efficiency rebates. TwinTech offered very useful advice on the make and model of furnace to choose including high efficiency and variable speed motor. The price was reasonable, TwinTech arrived at the allotted time, installed the new furnace (including some re-routing of exhaust lines since the existing ones were too close to other vents), removed the old furnace, tested the installation and cleaned everything up. Overall, it was a good experience, they did a great job and the new furnace is working well.
Related Links:
heat pump system cost, 5 ton heat pump, indoor heat pumps, heat pump technology, residential heat pump system, heat pump hvac system, heat pump,