Durham Region Air Conditioning Repair, Service and Installation
If you're looking for help fixing your Heil furnace, look no further! Our comprehensive Heil furnace repair guide will explain common issues, provide troubleshooting tips, and show you how to read your model's error codes..
CODE: Heartbeat.
RESULT: Control has 24 VAC power.
RESULT: Control has 24 VAC power.
CODE: 2 Flashes.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
CODE: 3 Flashes.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
CODE: 4 Flashes.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
CODE: 5 Flashes.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
CODE: 6 Flashes.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
CODE: 7 Flashes.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
CODE: 8 Flashes.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
CODE: 10 Flashes.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
CODE: 1 + 2 Flashes.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
CODE: 6 + 1 Flashes.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
CODE: LED Off.
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
CODE: LED On.
RESULT: Control circuitry lockout- Auto-reset after one hour.
RESULT: Control circuitry lockout- Auto-reset after one hour.
CODE: LED SOLID.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
See What Our Customers Are Saying:
Aug 20, 2022
From quote, to installation, to follow up, Twintech provided excellent service. I would highly recommended their services.
Aug 19, 2022
I had a really great experience with these guys. The salesman Bob was clearly very knowledgeable about everything to do with heating and cooling a home, spent a lot of time with us going over the details of the job, never rushed us and came back after the install to make sure we were happy. The installation crew was excellent, they covered the floors all the way from outside down to the basement furnace room, kept the place clean, got the work done on time and were very friendly. Ive got 15 years in the contracting/ construction industry and these guys are one of the most professional companys Ive dealt with. Great company!
Aug 18, 2022
Had great service and clean-up was good. Was happy with my salesman. They were very friendly and helpful. I needed a new furnace as our was over 20 years old. The furnace and air-conditioner work great and they are very quiet. I am very pleased with the service and product I received.
Aug 17, 2022
Met with Dave for the sales process and he was great about explaining and going over everything to us. The install happened very quickly and the team were super professional and friendly. We are very happy with this company and their services and we definitely recommend them to others. Thankful my sister recommended them to me!
Aug 16, 2022
Reviews for Twintech were good, and they did not disappoint. After an initial visit to discuss the suitable AC unit for replacement, an installation date was available in just a couple of days, and everything was installed without a hitch. Highly recommended
Aug 16, 2022
Very pleased with the installation of our new furnace and A/C unit. From quotation stage to the completion of the job Twintech was very professional.
Thank you for a job well done.
Aug 15, 2022
My old water heater quit on me. I called TwinTech. In less than 4 days, I had my new water heater installed and the old one taken away. The whole process was quick, easy, pleasant, and well done. This is the third time I've dealt with TwinTech and I've been satisfied each time.
Aug 14, 2022
I had them replace my furnace last year. When it came time for the air conditioner this year, I did not hesitate to call Twintech again. I will also have them perform regular maintenance on them.
Aug 13, 2022
We required a new HVAC replacement after running the old
system for 18 years.
Dave understood our requirements and gave us a quote that
covered all the necessary items.
Installation was fast and very tidy. Everything works as
it should. Our thanks to Greg, Mitch and others for their
excellent work. Recommend this family owned business to
anyone else, considering HVAC or other work.
Aug 12, 2022
I needed a new furnace and A/C to replace my 21 yr. old units, and went to the internet to view potential companies in May, I received 3 quotes,
and chose Twintech based on their salesman Dave who was very detailed and covered off everything on what Twintech was all about,
an extremely dedicated company with so many years of experience, and after reading the on line reviews I was sold on Twintech, who did not disappoint as the installation team were top notch with Greg leading,
I would highly recommend this company without any doubts, in my books they are first class all the way. Our new Amana furnace and A/C are working perfectly !