Durham Region Air Conditioning Repair, Service and Installation
If you're looking for help fixing your Heil furnace, look no further! Our comprehensive Heil furnace repair guide will explain common issues, provide troubleshooting tips, and show you how to read your model's error codes..
CODE: Heartbeat.
RESULT: Control has 24 VAC power.
RESULT: Control has 24 VAC power.
CODE: 2 Flashes.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
RESULT: Pressure switch did not open, check for obstructed pressure tubing.
CODE: 3 Flashes.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
RESULT: Pressure switch did not close, or re-opened- Check for: excessive wind, proper vent size, defective inducer motor, low inducer voltage, defective pressure switch, inadequate combustion air supply, disconnected or obstructed pressure tubing, low inlet gas pressure, restricted vent, condensate clogged.
CODE: 4 Flashes.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
RESULT: Limit circuit fault-a limit or flame rollout is open. Check for: restricted vent, proper vent sizing, loose blower wheel, excessive wind, dirty filter, defective blower motor, defective switch or connections, inadequate combustion air supply.
CODE: 5 Flashes.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
RESULT: Abnormal flame proving signal-Flame is proved while gas valve is de-energized. Check for: leaky gas valve, stuck open gas valve.
CODE: 6 Flashes.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
RESULT: Failure to ignite or flame sense lost while running. Check for: Flame sensor must not be grounded, low inlet gas pressure, oxide buildup on flame sensor, Manual valve shut off, proper flame sense microamps, gas valve defective or gas valve turned off, defective hot surface igniter, control ground continuity, Inadequate flame carryover or rough ignition, green/yellow wire MUST be connected to furnace sheet metal.
CODE: 7 Flashes.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
RESULT: Limit circuit lockout- Lockout occurs if the limit or flame rollout is open longer than 3 minutes. Control will auto reset after 3 hours. Refer to #4.
CODE: 8 Flashes.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
RESULT: Gas heating lockout-Control will NOT auto reset. Check for: mis-wired gas valve, defective control valve.
CODE: 10 Flashes.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
RESULT: Polarity-Line voltage, polarity reversed. If twinned, refer to twinning kit instructions.
CODE: 1 + 2 Flashes.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
RESULT: Blower on after power up- Blower runs for 90 seconds, if unit is powered up during a call for heat (R-W closed) or (R-W) opens during blower on delay.
CODE: 6 + 1 Flashes.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
RESULT: Ignition lockout- Control will auto-reset after 3 hours. Refer to #6.
CODE: LED Off.
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
RESULT: Secondary voltage fuse is open- Check for: door switch not closed, 115VAC at L1 and neutral, 24VAC RED and COM BLUE, 24V Fuse 3A, short circuit in secondary voltage (24VAC wiring).
CODE: LED On.
RESULT: Control circuitry lockout- Auto-reset after one hour.
RESULT: Control circuitry lockout- Auto-reset after one hour.
CODE: LED SOLID.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
RESULT: Gas valve relay stuck open- Flame sense circuit failure, software check error, reset power to clear lockout, replace control if status code repeats.
See What Our Customers Are Saying:
Apr 28, 2022
We had a great experience. The guys who installed our a/c did a nice job. Cleaned up.
Apr 28, 2022
excellent crew, fast and efficient! Would call them again when I need a new furnace.
Apr 28, 2022
Professional, courteous and efficient, dont need to say more than that! Use them you will not regret it.
Apr 28, 2022
TwinTech was a pleasure to deal with from the estimate through installation. We replaced a 28 year old a/c unit with one recommended by TwinTech's sales representative Dave who took the time to go over the product with us and answer any questions. The warranty is for 10 years parts and labour and they will complete the registration for you. Installation was by Greg (owner) and Mitch and Spencer who were quick and efficient and left everything clean and tidy.
Apr 28, 2022
Very professional, from the sales consultation and inspection to the final installation. Met every expectations we had for the job. A local business with great client support. We highly recommend. Twintech is a blue chip! Thanks!
Apr 28, 2022
I left a live chat message on their website that my air conditioning was not working. Within 1hr a representative called me to discuss my options.
The next day he came to the house to review my needs and give me a price for a new system. Price quoted was less than I expected and the installation was completed the following day. I found their salesman and the installers very knowledgeable and easy to deal with. All my questions were answered. Everything was properly explained in regards to what unit was needed and why, along with instruction where needed for use.
The installers made sure everything was working properly before they left.
Apr 28, 2022
This is to thank Twintech Heating and Cooling for their exceptional and timely service. Mitch, their technician was very courteous and generous with his time right from his first meeting with us. He not only took the time to check everything but also educated us on why we needed what he recommended. Greg and Mitch graciously accommodated us on our requested day and time for job to be done. They were both very courteous and responsive to our needs and special requests especially in a tight spot. The job was finished neatly and on time. Thank you Twintech for your great service !
Apr 28, 2022
They came the day and time they had planned for us and were very fast and efficient! The AC works amazing and it is amazing during the heat of the summer we have already got! Thanks for everything you did for us!
Apr 28, 2022
Would recommend this company to friends and family in a heartbeat. Very professional , on time and left no mess when the job was done.
Apr 28, 2022
Great customer service. Responsive and professional. I would highly recommend Twintech, I used them previously for repair service and a new air conditioner- very satisfied.