Durham Region Air Conditioning Repair, Service and Installation
If you're looking for help fixing your tempstar furnace, look no further! Our comprehensive tempstar repair guide will explain common issues, provide troubleshooting tips, and show you how to read your model's error codes.
CODE: Heartbeat LED pattern on solid.
RESULT: The control is locked out and will auto-reset after 1 hour.
FIX: Reset power to clear the lockout.
RESULT: The control is locked out and will auto-reset after 1 hour.
FIX: Reset power to clear the lockout.
CODE: Two LED flashes.
RESULT: Pressure switch didn't open.
FIX: Obstructed pressure tubing; a pressure switch that's stuck closed.
RESULT: Pressure switch didn't open.
FIX: Obstructed pressure tubing; a pressure switch that's stuck closed.
CODE: Three LED flashes.
RESULT: The low-pressure switch did not close or has reopened.
FIX: Proper vent sizing; air leak; restricted vent; clogged condensate drain; low input gas pressure; excessive wind; improper pressure switch wiring; water in vent piping; disconnected or obstructed pressure tubing.
RESULT: The low-pressure switch did not close or has reopened.
FIX: Proper vent sizing; air leak; restricted vent; clogged condensate drain; low input gas pressure; excessive wind; improper pressure switch wiring; water in vent piping; disconnected or obstructed pressure tubing.
CODE: Four LED flashes.
RESULT: Limit circuit fault.
FIX: Loose blower wheel; defective switch or connections; improper minimum- or maximum-heat gas input adjustment; dirty filter or restricted duct system; improper limit switch.
RESULT: Limit circuit fault.
FIX: Loose blower wheel; defective switch or connections; improper minimum- or maximum-heat gas input adjustment; dirty filter or restricted duct system; improper limit switch.
CODE: Five LED flashes.
RESULT: Abnormal flame-proving signal.
FIX: Leaky gas valve; stuck-open gas valve.
RESULT: Abnormal flame-proving signal.
FIX: Leaky gas valve; stuck-open gas valve.
CODE: Six LED flashes.
RESULT: Ignition proving a failure.
FIX: Low inlet gas pressure; control ground continuity; gas valve defect; defective hot surface igniter; oxide buildup on the flame sensor; inadequate flame carryover; flame sensor mustn't be grounded.
RESULT: Ignition proving a failure.
FIX: Low inlet gas pressure; control ground continuity; gas valve defect; defective hot surface igniter; oxide buildup on the flame sensor; inadequate flame carryover; flame sensor mustn't be grounded.
CODE: Seven LED flashes.
RESULT: Limit circuit lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #4.
RESULT: Limit circuit lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #4.
CODE: Eight LED flashes.
RESULT: Gas heating lockout.
FIX: Gas valve stuck closed on control.
RESULT: Gas heating lockout.
FIX: Gas valve stuck closed on control.
CODE: Nine LED flashes.
RESULT: Medium pressure switch, high-pressure switch, or PSR relay didn't close or was reopened.
FIX: Refer to status code #3.
RESULT: Medium pressure switch, high-pressure switch, or PSR relay didn't close or was reopened.
FIX: Refer to status code #3.
CODE: Ten LED flashes.
RESULT: Polarity.
FIX: Correct line voltage polarity.
RESULT: Polarity.
FIX: Correct line voltage polarity.
CODE: Status codes 1 + 2.
RESULT: Blower on after power up.
FIX: Normal operation.
RESULT: Blower on after power up.
FIX: Normal operation.
CODE: Status codes 1 + 5.
RESULT: Blower motor lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #4 + 1.
RESULT: Blower motor lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #4 + 1.
CODE: Status codes 3 + 5.
RESULT: Gas valve fault.
FIX: RED, YELLOW, or ORANGE wire at the gas valve.
RESULT: Gas valve fault.
FIX: RED, YELLOW, or ORANGE wire at the gas valve.
CODE: Status codes 4 + 1.
RESULT: Blower motor fault.
FIX: Blower failed to reach 250 RPM, or the blower failed to communicate within the prescribed time limits.
RESULT: Blower motor fault.
FIX: Blower failed to reach 250 RPM, or the blower failed to communicate within the prescribed time limits.
CODE: Status codes 4 + 2.
RESULT: Inducer motor fault.
FIX: Proper vent sizing; restricted vent; failed inducer motor; improper motor wiring; a blockage in the tubing to the pressure switch assembly.
RESULT: Inducer motor fault.
FIX: Proper vent sizing; restricted vent; failed inducer motor; improper motor wiring; a blockage in the tubing to the pressure switch assembly.
CODE: Status codes 4 + 3.
RESULT: The low or medium pressure switch is open while the medium or high-pressure switch is closed.
FIX: Low inlet gas pressure; clogged condensate drain; improper pressure switch wiring; water in vent piping; low or medium pressure switch stuck open; disconnected or obstructed pressure tubing.
RESULT: The low or medium pressure switch is open while the medium or high-pressure switch is closed.
FIX: Low inlet gas pressure; clogged condensate drain; improper pressure switch wiring; water in vent piping; low or medium pressure switch stuck open; disconnected or obstructed pressure tubing.
CODE: Status codes 6 + 1.
RESULT: Ignition lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #6.
RESULT: Ignition lockout.
FIX: Control will auto-reset after 3 hours. Refer to status code #6.
See What Our Customers Are Saying:
Jan 1, 2015
My old furnace had finally broken down for the last time when contacted twintech to have a new furnace installed They were prompt, knowledgeable and very reasonably priced. They did such a great job i tell all my friends and family about this company.
Jan 1, 2015
To whom it may concern, I recently had TwinTech (Greg and Grant Dainty) replace my furnace and service both my gas fireplaces and air conditioning unit. They were professional, courteous and very fair in their pricing. I would gladly recommend TwinTech to anyone needing work done. I can be contacted at 905-626-XXXX.
Jan 1, 2015
My Fiancé and I have relied on Twintech Heating and Cooling now for the better part of the last 10 years. In that time, Greg has installed a furnace, an air conditioner, and a heat-pump at our residence in Toronto. In each instance Greg and his team were a pleasure to deal with. They were courteous and professional throughout the whole process and the quality of their work is first rate. Our experiences have always been extremely positive and we have referred his services numerous times to our friends and family. Without hesitation, I would recommend Greg and TwinTech Heating and Cooling to anyone looking to service or replace their existing heat/AC equipment
See What Our Customers Are Saying:
Feb 18, 2025
Very pleased with the professional service that TwinTech Heating and Cooling provided in replacing my furnace. I got several quotes from different service providers. Their price was excellent and they explained the features very well. We are very glad we went with TwinTech and highly recommend their services.
Feb 18, 2025
We were new homeowners in need of a second opinion. TwinTech Heating & Cooling were Amazing and professional. Very knowledgeable and great service all around. Recommend to anyone looking for honest and reliable services. Treated with respect and care. Thank you Greg, Mitch and Bob!
Feb 18, 2025
TwinTech is an excellent and honest company! I called them for a second opinion after being told by another company that I needed to replace my furnace. Turns out this was not the case at all! I did not need a new furnace. TwinTech did not push to make an unnecessary sale and saved me from a huge expense. Bob and Mitch were extremely professional and above all honest! I definitely recommend TwinTech!
Feb 18, 2025
Amazing experience with TwinTech Heating & Cooling! Their team was professional, knowledgeable, and efficient from start to finish. They installed my new furnace quickly and left everything spotless. The technicians took the time to explain everything and made sure I was comfortable with the system before they left. Great customer service and fair pricing. I highly recommend them for anyone needing HVAC services!
Feb 18, 2025
Great experience all around. Bob was sharp and easy to talk to, and Greg handled the installation perfectly. Would hire them again in a heartbeat.
Why Should I Install an Amana Heat Pump?
- SUBMITTED BY:
- TWINTECH HEATING & COOLING
- - November 8, 2023
Amana heat pumps are a popular choice for homeowners seeking efficient and reliable heating and cooling solutions. Here are several reasons why you might consider installing an Amana heat pump: Energy Efficiency: Amana heat pumps are
Read MoreTwintech: Outstanding AC Service in Durham Region
- SUBMITTED BY:
- TWINTECH HEATING & COOLING
- - August 27, 2024
When it comes to maintaining a comfortable home, a reliable air conditioning system is essential. In Durham Region, Twintech Heating & Cooling stands out for delivering outstanding AC service that homeowners can trust. Expertise You Can Rely O
Read MoreTwinTech: Expert Heat Pump Repair and Service in Pickering
- SUBMITTED BY:
- TWINTECH HEATING & COOLING
- - July 11, 2024
Expert Heat Pump Repair and Service in Pickering with TwinTech Heating and Cooling When it comes to maintaining a comfortable home environment, a reliable heat pump system is essential, especially in Pickering's varying climate. TwinTech He
Read MoreEverything You Need to Know About Furnace Maintenance
- SUBMITTED BY:
- TWINTECH HEATING & COOLING
- - November 7, 2024
Maintaining your furnace is crucial for keeping your home comfortable, safe, and energy-efficient, especially during the colder months. Regular furnace maintenance can prevent unexpected breakdowns, lower energy bills, and extend the lifespan of your
Read More