Categories
- AC Filters
- AC Repair
- Air Conditioner Maintenance
- Air Conditioner Repair
- Air Conditioners
- Air Conditioning Services
- Air Quality
- Cleaning Tips
- Cooling
- Duct System
- Ducted Air Conditioner
- Ductless Air Conditioner
- Emergency Repairs
- Energy Costs
- Expert Help
- Fans
- FAQ
- Filters
- Fireplaces
- Fun
- Furnace Installations
- Furnace Repairs
- Furnaces
- Gas Fireplaces
- Gas Line
- Gas Line Installations
- Heat Pumps
- Heating
- Heating and Cooling
- Heating Contractors
- heating system
- Heating Technicians
- Humidity
- HVAC
- HVAC Contractors
- HVAC experts
- HVAC Noises
- HVAC professionals
- HVAC Repairs
- HVAC Service
- Insulation
- Maintenance
- Natural Gas
- Pestibulum molestieenean
- Saving Money
- Water
- Water Heaters
- Work
[BACK]
Humidity issues with ducted Mitsubishi heat pump
Posted On: September 5, 2023
Hello, wondering if others have experienced difficulty maintaining comfortable humidity using a Mitsubishi hyper heat ducted system.
I think the heart of the matter is that they try to be too efficient and can maintain temp well but ignore the importance of humidity.
I have an old inefficient carrier ac downstairs which works great at keep the lower level cool and dry.
My upstairs unit is the heat pump.
I tend to use dry mode as it seems to work better than cool mode since it will try to run longer by keeping the fan speed low and the coil cold.
However, it only really significantly brings down humidity when it's first turned on.
And it does this really well initially.
It can drop eh by like 10% in an hour.
You can repeat this effect by continuing to lower the set point but then you just end up chasing uncomfortably cold temperatures to meet humidity.
If I set it at 74 it will cool until it hits 71 degrees, then shut off and kick back on when it reaches 73.
I could run a portable dehumidifier but they are loud, need to be emptied often unless you have a drain nearby, and consume lots of power.
If I could just hack this thing to run less efficient, ramp up the compressor hit a set point shut off and do it again I think It would be more comfortable.
Or come up with a way to schedule it so that the set point is at 74 then shuts off at 73, unit waits to turn back on at 75 and repeat.
Any thoughts or suggestions?
Thanks.
Question from user Ok-Swan2736 at heatpumps at reddit.
Answer:
Dry mode is 100% cooling.
It could also be that your unit is oversized.
You satisfy temp setpoint before pulling any moisture out of the air.
This is not the fault of your unit, but of your installers system selection.
Answer from user rayinreverse at heatpumps at reddit.
[BACK]
See What Our Customers Are Saying:
May 13, 2020
We are very happy with our new furnace. The service was excellent the guys worked 6 hours straight through and there was no mess at all they took the old furnace boxs etc with them they then explained everything to us they were very helpful and pleasant , when we need a new air conditioner we know who to call!
May 12, 2020
The crew from sales to installation was very professional and had great attention to detail
May 11, 2020
We couldnt have been more impressed with Twintech - from our first service call with Mitch who took the time to thoroughly diagnose the issue with our furnace, to Dave who proposed a well thought out solution to meet our needs and finally Greg and team who acted quickly to install given we had no heat.
We did our due diligence by soliciting quotes from alternate providers and were shocked and disappointed by the aggressive and manipulative tactics used.
Twintech was honest in their approach, detailed in their product knowledge, reasonably priced, diligent in their follow-up and valued our business.
Well done Twintech! You made this a positive experience for us and our new furnace works beautifully!
May 10, 2020
We recently purchased an Amana high efficiency furnace and humdifier through Twintech. The work was completed very professionally and the quality of the workmanship was high. There was some additional sheet metal work required to complete the installation, which they were able to complete themselves. Overall I am very pleased with the work and would highly recommend Twintech for a furnace replacement.
May 9, 2020
We were very pleased with every aspect of the work that was done. They were very professional and polite. They arrived when they said they would and job was completed on estimated time
We would highly recommend them to whoever needed a recommendation
We have a very large dog and they were very understanding and respectful of him being around
May 8, 2020
The blower on our furnace stopped working leaving us with a cold house. Dave from TwinTech responded immediately to our HomeStars service request. From beginning to end Dave was nothing but helpful, friendly and professional, he did a great job of walking us through the quote and scope of work.
The replacement of the furnace went smoothly. The Guys did a great job, everyone was very friendly and polite. There were no hiccups, or unexpected costs. The only surprise was they left the work area cleaner than it was before they started.
Was a great experience with the whole TwinTech team. Its been a couple of months since the new furnace has been installed and its working great!
May 7, 2020
I heard about TwinTech when researching new furnaces at furnaceprices.ca. After contacting them about my broken down furnace, Dave came to my house the next day to assess my situation and requirements for a new furnace. He recommended one that had stainless steel heat exchangers which sold me since my previous furnace had issues with a rusted secondary heat exchanger that had to be replaced. Dave also set me up with an appointment with an energy audit company so that I could take advantage of a rebate to help improve the energy efficiency of my home and get some money back. A few days later, Greg, Grant, and Mitch came to install the new furnace and remove the old one. When delivering and removing the furnaces, they were very careful not to damage my floors and walls, and even laid out red carpeting to protect the floors. They were very friendly and professional. The installation was completed in the time they said it would take and they cleaned up their work areas. Within a week, Dave called to follow-up to see how everything was going. I have already recommended them to several friends and family members who may need new furnaces soon.
May 6, 2020
Twintech did a great job, from Dave the Sales Rep to the Office staff and The Professional Technicians who did the installation. They were professional, courteous, knowledgable and informative. From beginning to follow up we were completely satisfied with everything. Thanks Again. Sincerely The Laytons
May 5, 2020
Great product, great service, great follow-up. The Twintech Heating and Cooling arranged removal of my existing oil tank and they installed the new gas furnace Amana (made in USA). I am very happy with the final result and support I received throughout the process. My thanks go to the entire Twintech team for their professionalism, great communication and follow-up.
May 4, 2020
We've had Twintech provide us with work in the past, for an inground pool heater and required rough-in for a new gas stove. More recently they provided the same friendly, professional, timely and clean installation of our new furnace.
Related Links:
ductwork installation, ductless ac system, ductless ac unit,