Categories
- AC Filters
- AC Repair
- Air Conditioner Maintenance
- Air Conditioner Repair
- Air Conditioners
- Air Conditioning Services
- Air Quality
- Cleaning Tips
- Cooling
- Duct System
- Ducted Air Conditioner
- Ductless Air Conditioner
- Emergency Repairs
- Energy Costs
- Expert Help
- Fans
- FAQ
- Filters
- Fireplaces
- Fun
- Furnace Installations
- Furnace Repairs
- Furnaces
- Gas Fireplaces
- Gas Line
- Gas Line Installations
- Heat Pumps
- Heating
- Heating and Cooling
- Heating Contractors
- heating system
- Heating Technicians
- Humidity
- HVAC
- HVAC Contractors
- HVAC experts
- HVAC Noises
- HVAC professionals
- HVAC Repairs
- HVAC Service
- Insulation
- Maintenance
- Natural Gas
- Pestibulum molestieenean
- Saving Money
- Water
- Water Heaters
- Work
[BACK]
What Do These Furnace Error Codes Mean?
Posted On: September 21, 2024
Furnace error codes are diagnostic signals that help identify problems with the furnace's operation. Each code represents a specific issue that needs to be addressed, typically related to components like the thermostat, sensors, or burners. Here's a breakdown of some common furnace error codes:
1. Error Code 1 Flash:
- Issue: Furnace is in a lockout mode.
- Meaning: This typically happens after three failed ignition attempts. The furnace will shut down for safety reasons.
- Solution: Reset the furnace or call a technician to check the ignition system.
2. Error Code 2 Flashes:
- Issue: Pressure switch stuck closed.
- Meaning: The pressure switch monitors the venting system. If it’s stuck, it means the furnace might be having issues with the venting process.
- Solution: Check for blockages in the vent pipe or replace the pressure switch.
3. Error Code 3 Flashes:
- Issue: Pressure switch stuck open.
- Meaning: The switch is open when it should be closed during normal furnace operation.
- Solution: Ensure the vent pipes are clear, and the switch is functioning properly.
4. Error Code 4 Flashes:
- Issue: Limit switch open.
- Meaning: The limit switch is a safety device that shuts off the furnace if it overheats.
- Solution: Check for restricted airflow due to dirty filters or obstructed vents.
5. Error Code 5 Flashes:
- Issue: Flame sensor failure.
- Meaning: The furnace cannot detect a flame, which could indicate a dirty or faulty flame sensor.
- Solution: Clean the flame sensor or replace it if necessary.
6. Error Code 6 Flashes:
- Issue: Ignition lockout.
- Meaning: After three failed ignition attempts, the furnace will enter lockout mode.
- Solution: Check the gas supply and ignition system, and reset the furnace.
7. Error Code 7 Flashes:
- Issue: Gas valve stuck closed.
- Meaning: The furnace cannot get the gas needed for combustion.
- Solution: Inspect the gas valve and ensure it’s operating correctly.
8. Error Code 8 Flashes:
- Issue: Low voltage issue.
- Meaning: The furnace is not receiving adequate power to function properly.
- Solution: Check the electrical connections and wiring to the furnace.
Each brand of furnace may have different error codes, so it's important to refer to the furnace’s manual for specific meanings or call a professional HVAC technician if you're unsure about any particular code.
[BACK]
See What Our Customers Are Saying:
Jan 1, 2015
My old furnace had finally broken down for the last time when contacted twintech to have a new furnace installed They were prompt, knowledgeable and very reasonably priced. They did such a great job i tell all my friends and family about this company.
Jan 1, 2015
To whom it may concern, I recently had TwinTech (Greg and Grant Dainty) replace my furnace and service both my gas fireplaces and air conditioning unit. They were professional, courteous and very fair in their pricing. I would gladly recommend TwinTech to anyone needing work done. I can be contacted at 905-626-XXXX.
Jan 1, 2015
My Fiancé and I have relied on Twintech Heating and Cooling now for the better part of the last 10 years. In that time, Greg has installed a furnace, an air conditioner, and a heat-pump at our residence in Toronto. In each instance Greg and his team were a pleasure to deal with. They were courteous and professional throughout the whole process and the quality of their work is first rate. Our experiences have always been extremely positive and we have referred his services numerous times to our friends and family. Without hesitation, I would recommend Greg and TwinTech Heating and Cooling to anyone looking to service or replace their existing heat/AC equipment
Related Links:
oshawa gas furnace problems, ajax furnace inspection, whitby furnace replacement, furnace repairs pickering, oshawa hvac furnaces, pickering gas furnace problems, whitby furnaces, residential furnace, pickering hvac furnace, pickering furnace service, pickering furnaces, oshawa furnace inspection, oshawa furnaces, gas furnace problems, furnace services oshawa, furnace maintenance near me, furnace repair ajax, furnace repair pickering, furnace repair oshawa, furnace replacement, furnace repairs, furnace repair, furnace installations ajax, furnace installations pickering, furnace installations oshawa, furnace inspection,