$49 / month O.A.C Including Install
$49 / month O.A.C Including Install

24 / 7 Emergency Service Available. Call Us Now: 1.844.894.6832

Durham Region Air Conditioning Repair, Service and Installation

CLICK HERE FOR A FREE QUOTATION

Each of the following status codes is a two digit number with the first digit determined by number of flashes of the yellow led and the second digit determined by number of flashes of the green led.


Like many furnace manufacturers, Bryant uses flashing LED lights to indicate error codes that can give you an idea of what's wrong with your furnace when it's not functioning properly. The short flashes indicate the first digit of the two-digit code, and the long flashes indicate the second digit. Here's are some common error codes.


CODE: RED LED1 ON.
RESULT: Furnace is operating in emergency heat.

CODE: RED LED2 ON.
RESULT: The microprocessor has malfunctioned. To reset: Put setup switch "SW-1" in the "ON" position nad jumper thermostat terminals "R", "W/W1" and "Y/Y2" simultaneously with the door switch pushed in and power to the unit "ON". Disconnect jumper and place setup switch in the "OFF" position. If LED2 reappears, replace main control board.

CODE: YELLOW LED3 ON.
RESULT: Furnace is operating in high heat.

CODE: GREEN LED4 ON.
RESULT: Furnace is operating in low heat.

CODE: RED LED2 FLASHING.
RESULT: Line voltage polarity is reversed.

CODE: 1-1.
RESULT: NO FAULT IN RECENT HISTORY DISPLAY
FIX: Indicates no faults have occurred within the last five cycles. To read recent fault history, put setup switch "SW-1" in the "ON" position. To clear recent fault history, put setup switch "SW-1" in the "ON" position and jumper thermostat terminals "R", "W/W1" and "Y/Y2" simultaneously until an "11" is flashed.

CODE: 1-2.
RESULT: BLOWER CALIBRATION LOCKOUT
FIX: Indicates RPM calculated for low heat was less than 250 RPM or greater than 1300 RPM on two successive attempts. Auto reset after three hours. Reset power and refer to fault #44 section.

CODE: 1-3.
RESULT: LIMIT SWITCH LOCKOUT
FIX: Indicates the occurrence of 10 successive limit trips during high heat or three successive limit trips during low heat. Auto reset after three hours. Check for *Improper or misaligned limit and/or limit shield. *Improper high or low heat gas input adjustment. *Stuck high heat solenoid in gas valve.

CODE: 1-4.
RESULT: IGNITION LOCKOUT
FIX: Control will auto-reset after three hours.

CODE: 2-1.
RESULT: INVALID MODEL SELECTION
FIX: Indicates model plug is missing or incorrect. See wiring diagram for correct connector jumper location.

CODE: 2-2.
RESULT: SETUP ERROR
FIX: Indicates setup switch "SW-1" or "SW-6" is positioned improperly. The following combinations will cause the fault: *Thermostat call with "SW-1" "ON", or Thermostat call with "SW-6" "ON", or "SW-1" and "SW-6" both "ON" together.

CODE: 2-3.
RESULT: INVALID BLOWER AIRFLOW SELECTION
FIX: Indicates improper "A/C" or "CF" switch setting. The 042 and 14 units can deliver 1-1/2 to 3-1/2 tons A/C and 600 to 1400 CFM for continuous fan. The 060 and 20 unit can deliver 2 to 5 tons A/C and 800 to 2000 CFM for continuous fan. If code is flashing, unit will default tp closest allowable airflow.

CODE: 2-4.
RESULT: SECONDARY VOLTAGE FUSE IS OPEN
FIX: Check for: - Short circuit in secondary voltage (24VAC) wiring.

CODE: 3-1.
RESULT: PRESSURE SWITCH DID NOT CLOSE OR REOPENED
FIX: If open longer than five minutes, inducer shuts off for 15 minutes before retry. Check for: - Excessive wind - Proper vent sizing -- Defective inducer motor - Low inducer voltage (115VAC) - Defective pressure switch -Inadequate combustion air supply - Restricted vent - Disconnected or obstructed pressure tubing - Low inlet gas pressure (if LGPS used) If it opens during blower ondelay period, blower will come on for the selected blower off-delay.

CODE: 3-3.
RESULT: LIMIT CIRCUIT FAULT
FIX: Indicates a limit, or flame rollout is open. Blower will run for 4 minutes or until open switch remakes whichever is longer. If open longer than 3 minutes, code changes to lockout #13. If open less than 3 minutes status code #33 continues to flash until blower shuts of Flame rollout switch requires manual reset. Check for: - Restricted vent - Proper vent sizing - Loose blower wheel - Excessive wind - Dirty filter or restricted duct system. - Defective blower motor or capacitor. - Defective switch or connections. - Inadequate combustion air supply (Flame Roll-out Switch open).

CODE: 3-4.
RESULT: IGNITION PROVING FAILURE
FIX: Control will try three more times before lockout #14 occurs. If flame signal lost during blower on-delay period, blower will come on for the selected blower off-delay. Check for: - Control ground continuity - Flame sensor must not be grounded - Oxide buildup on flame sensor (clean with fine steel wool) - Proper flame sense microamps (.5 microamps D.C. min., 4.0 - 6.0 nominal). - Gas valve defective or gas valve turned off - Manual valve shut-off - Defective Hot Surface Ignitor - Low inlet gas pressure - Inadequate flame carryover or rough ignition - Green/Yellow wire MUST be connected to furnace sheet metal.

CODE: 4-1.
RESULT: BLOWER OUTSIDE VALID SPEED RANGE
FIX: Indicates the blower is not operating at the calculated RPM. If this fault occurs in conjunction with fault #44 check wiring to motor otherwise refer to the trouble-shooting guide.

CODE: 4-2.
RESULT: INDUCER OUTSIDE VALID SPEED RANGE
FIX: Indicates the inducer is not operating at the calculated RPM. Or it has not started within 10 seconds after a call for heat. Check wiring to motor otherwise refer to the troubleshooting guide.

CODE: 4-3.
RESULT: PRESSURE SWITCH CALIBRATION FAULT
FIX: Indicates the low and high pressure switch "make" points during high heat purge are not within calibration range. Check for: -Plugged condensate drain Water in vent piping, possibly sagging pipe -Improper pressure switch wiring or pressure switch tubing connections -Failed or "out of calibration" pressure switches.

CODE: 4-4.
RESULT: BLOWER CALIBRATION FAULT
FIX: Indicates the calculated blower speed is below 250 or above 1300 RPM. Unit will default to low or high heat mode if possible. If this fault occurs in conjunection with fault #41, check wiring to motor otherwise refer to the trouble shooting guide. If this fault occurs by itself, check for undersized ductwork, or excessive static caused by a dirty filter, or closed registers.

CODE: 4-5.
RESULT: CONTROL CIRCUITRY LOCKOUT
FIX: Auto-reset after one hour lockout due to; - Gas valve relay stuck open - Flame sense circuit failure - Software check error Reset power to clear lockout. Replace control if status code repeats.


See What Our Customers Are Saying:

by Kevin, Toronto on Twintech Heating and Cooling

We contacted TwinTech after having another ductless air-conditioning company come in to quote on a solution for our townhouse. We had a unique problem where my office was a hot spot - it's at the front of the unit and gets a lot of sun. If it's 20C outside, It's 29C in my office. The other company could not build a solution that would get a ductless unit to that room because of the location - the AC unit would have to be at the rear, and ductless systems would have to be on that side of the interior. TwinTech suggested a hybrid solution to fit our unique problem, where the ductless unit would move cold air to an air exchanger installed in our bedroom closet, and then they built a ducted vent system between all the upper rooms. This was less intrusive than building a central air system, and less expensive. Each room has a vent that I can close off, so I can push more cold air to my office when needed. We really didn't want ductless units sitting on the walls, and this looks and works better. I really appreciate the extra thought and care that went into the design of a solution, and the attention to detail in the installation. They answered all of our questions, and were able to do a bit extra by installing the ducts around the vents and painting them for us. It cost more than we originally planned for, due to our unique needs, but the fact that they offered financing helped us budget for more.
The job was done fast (I think we got lucky with timing where it wasn't the AC install busy season yet), and the team was very friendly and professional. They arrived and finished each day when they said they would. My office is now running at a comfortable temperature! I'm extremely happy with the experience and would whole heartedly recommend them.

by Private User on Twintech Heating and Cooling

How lucky are we to have this team come save us from our broken down, under sold, poorly installed previous unit (mind you there is a reason SEARS went bankrupt). Bob arrived on time to give us a detailed review of our unit and furnace; very knowledgeable. Greg arrived as planned with the new unit and reiterated what Bob explained how our furnace is equipped to handle the new unit and we didnt need to spend more money on a variable speed air conditioner. Cant say enough on how professional, efficient and personable this team is. Thank you so much guys!

by Private User on Twintech Heating and Cooling

We used Twintech for our replacement AC. Bob did a great job assessing what we needed and organized the install and showed up on install date. Greg and Mitch were on time and were very neat. They covered the traffic areas with a drop cloth and did an excellent install. Great clean up after install complete. Would recommend Twintech for heating and cooling.

by Private User on Twintech Heating and Cooling

They were fantastic, clean, freindly, great service. Would definitely recommend. Answered ally questions and more.

by Private User on Twintech Heating and Cooling

We woke up at about 7 a.m. the Sunday morning before Valentine's Day to a house that was barely 15 degrees Celsius on a really cold day. We tried to call some other suppliers but no answer or call back. We did a quick google search and Twintech came up. Had never dealt with them before. They had a chat line and lo & behold, someone answered; Greg. Helped us diagnose that our 40 year old furnace pilot light was out and walked us through how to relight it. All worked well; he even called me during this process. No charge I was told when asked.
15 minutes later, the pilot went out. It would not stay lit. Greg had Bob call us and we set up a meeting for about 11 a.m. that same Sunday.
Bob walked us through the options and even brought 3 electric space heaters for us to use. By Tuesday afternoon, we had a new Furnace and central air installed.

The team was helpful, responsive and respectful. Very glad we found them by accident and looking forward to a nice cool summer after a warm winter.

Thanks guys!

by Furnace And Humidifier Install on Twintech Heating and Cooling

Dealing with Bob and the installation crew was a pleasure. They took the time to explain everything. What would benefit us the most and the price difference. They were in and out in a reasonable time frame and fit us in within a couple days of original meeting. Quality of work is excellent as well.

by Private User on Twintech Heating and Cooling

A pleasure dealing with Bob ,Spencer and Mitch . They are professional and they also observe the covid 19 precautions . Bob explained the whole process and got the new furnace up the next day . Highly recommend

by Gary Monson, Ajax on Twintech Heating and Cooling

Would like to thank TwinTech for their quick response to our furnace repair. We used TwinTech to install a new furnace and AC a few years
back. Our furnace started to have problems early in the evening of extremely cold night. Contacted TwinTech and they were able make a service call later that evening. They got the furnace going and came the next day to replace a part. The part was under warranty and there was
no charge for either service call!
We are extremely happy with their customer service and would highly recommend them.
Gary & Kelly

by Paul, Toronto on Twintech Heating and Cooling

This is the second time we have had Twintech to our house. A couple of summers ago they were in for an issue with our air conditioning. This time it was our furnace having an issue. It was shutting off randomly and not coming back on. Greg came right away and took the time to investigate thoroughly and explain what was going with the furnace. Both times I have been thoroughly impressed with their speed, customer service, and quality of work. I HIGHLY recommend Twintech.

by Private User on Twintech Heating and Cooling

Extremely happy.
So we were in no rush to replace our old units and took the time to do some research and get a number of quotes.
Twintech came in at around the middle of the pack for price but what convinced us to go with them was Bob, the representative that came to our house. Bob was by far the most professional of all the reps that we met with. He took the time to explain everything, what would work best for us and why. He really did seem very knowledgeable and enthusiastic about his stuff.
As promised on the day of install the crew showed up on time and got to work with minimal impact on us
..they were professional, clean, tidy and got the system up and running ahead of schedule...they made a couple of adjustments to the system to optimize it for our house.
The crew left the house clean and tidy.
Bob the rep showed up to check in and give us a few tips ..
It's been a week since install and all is good.
Our overall experience with Twintech has been excellent from start to finish and I wouldn't hesitate to recommend them.
Thank u.

See What Our Customers Are Saying:

by Robert Rogers on Twintech Heating and Cooling

Very pleased with the professional service that TwinTech Heating and Cooling provided in replacing my furnace. I got several quotes from different service providers. Their price was excellent and they explained the features very well. We are very glad we went with TwinTech and highly recommend their services.

by Robert Mizuno on Twintech Heating and Cooling

We were new homeowners in need of a second opinion. TwinTech Heating & Cooling were Amazing and professional. Very knowledgeable and great service all around. Recommend to anyone looking for honest and reliable services. Treated with respect and care. Thank you Greg, Mitch and Bob!

by Ruth on Twintech Heating and Cooling

TwinTech is an excellent and honest company! I called them for a second opinion after being told by another company that I needed to replace my furnace. Turns out this was not the case at all! I did not need a new furnace. TwinTech did not push to make an unnecessary sale and saved me from a huge expense. Bob and Mitch were extremely professional and above all honest! I definitely recommend TwinTech!

by Anna Chin on Twintech Heating and Cooling

Amazing experience with TwinTech Heating & Cooling! Their team was professional, knowledgeable, and efficient from start to finish. They installed my new furnace quickly and left everything spotless. The technicians took the time to explain everything and made sure I was comfortable with the system before they left. Great customer service and fair pricing. I highly recommend them for anyone needing HVAC services!

by Connor Agnew on Twintech Heating and Cooling

Great experience all around. Bob was sharp and easy to talk to, and Greg handled the installation perfectly. Would hire them again in a heartbeat.

What's the Best Way to Use My Gree Heat Pump to Save on Electricity?

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - October 15, 2023

To maximize energy savings and efficiency when using a Gree heat pump, you can follow these tips: Set the Thermostat Wisely: Use a programmable or smart thermostat to maintain consistent temperatures. Set lower temperatures during th

Read More

When's the Last Time You Had Your Furnace Serviced?

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - November 27, 2024

When’s the Last Time You Had Your Furnace Serviced As temperatures drop, your furnace becomes the unsung hero of your home, keeping your space warm and comfortable. But like any hardworking appliance, it requires regular maintenance to perf

Read More

Is My Furnace Unit Oversized?

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - December 19, 2024

An oversized furnace can lead to several issues, such as increased energy costs, uneven heating, and shorter equipment lifespan. To determine if your furnace unit is oversized, consider the following signs: 1. Short Cycling If your furnace f

Read More

Amana Heat Pump Maintenance Tips

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - September 9, 2023

Maintaining your Amana heat pump is crucial for optimal performance and energy efficiency. Here are some general maintenance tips to help you keep your Amana heat pump in good condition: Regularly Clean or Replace Air Filters: Dirty

Read More