$49 / month O.A.C Including Install
$49 / month O.A.C Including Install

24 / 7 Emergency Service Available. Call Us Now: 1.844.894.6832

Durham Region Air Conditioning Repair, Service and Installation

CLICK HERE FOR A FREE QUOTATION

Armstrong Air is the professional's choice in home heating & cooling. Including oil & gas furnaces, air conditioners, heat pumps, package units & air handlers.


CODE: E105.
RESULT: Device communication problem - No other devices on RS BUS (Communicating systems only).
FIX: Equipment is unable to communicate indicates numerous message errors. In most cases errors are related to electrical noise. Make sure high voltage power is separated from RSBus. Check for mis-wired and/or loose connections between the stat, indoor unit and outdoor unit. Check for a high voltage source of noise close to the system. Fault clears after communication is restored.

CODE: E110.
RESULT: Low line voltage.
FIX: Line Voltage low (Voltage tower than nameplate rating). Check power line voltage and correct. Alarm clears 5 seconds after fault recovered.

CODE: E111.
RESULT: Line voltage polarity reversed.
FIX: Reverse line power voltage wiring. System resumes normal operation 5seconds after fault recovered.

CODE: E112.
RESULT: Ground not detected.
FIX: System shuts down. Provide proper earth ground. System resumes normal operation 5 seconds after fault recovered.

CODE: E113.
RESULT: High line voltage.
FIX: Line Voltage high (Voltage higher than nameplate rating). Provide power voltage within proper range. System resumes normal operation 5seconds after fault recovered.

CODE: E114.
RESULT: Line voltage frequency out of range.
FIX: No 60 Hertz power. Check voltage and line power frequency. Correct voltage and frequency problems. System resumes normal operation 5seconds after fault recovered.

CODE: E115.
RESULT: Low 24V.
FIX: 24 Volt Power high (Range is 18 to 30 Volts). Check and correct voltage. Check for additional power robbing equipment connected to system. May require installation of larger VA transformer to be installed in furnace/air handler. Clears after fault recovered.

CODE: E116.
RESULT: High 24V.
FIX: 24 Volt Power high (Range is 18 to 30 Volts) Check and correct voltage. Check for proper line voltage (120V 240V etc) to equipment. Clears when control senses proper voltage.

CODE: E117.
RESULT: Poor ground detected (Warning only).
FIX: Provide proper grounding for unit. Check for proper earth ground to the system. Warming only will clear 30 seconds after fault recovered.

CODE: E120.
RESULT: Unresponsive device (Communicating systems only).
FIX: Usually caused by delay in outdoor unit responding to indoor unit poling. Recycle power. Check all wiring connections. Cleared after unresponsive device responds to any inquiry.

CODE: E124.
RESULT: Active communicating thermostat signal missing for more than 3 minutes (Communicating systems only).
FIX: Equipment lost communication with the thermostat. Check four wiring connections, ohm wires, and cycle power at the thermostat. Alert stops all services and waits for heart beat message from thermostat (subnet controller). Cleared after valid thermostat (subnet) message is received.

CODE: E125.
RESULT: Control failed self check, internal error, failed hardware. Will restart if error recovers, Integrated control not communicating Covers hardware errors (flame sense circuit faults, pin shorts, etc).
FIX: Hardware problem on the control. Cycle power on control. Replace if problem prevents service and is persistent. Cleared 300 seconds after fault recovered.

CODE: E126.
RESULT: Control internal communication problem.
FIX: Hardware problem on the control. Cycle power on control. Replace if problem prevents service and is persistent. Cleared 300 seconds after fault recovered.

CODE: E131.
RESULT: Corrupted control parameters (Verify configuration of system) (Communicating systems only).
FIX: Reconfigure the system. Replace control if heating or cooling is not available. Only applicable in the communicating mode not in startup. Exit from Commissioning and Execute Se+ factory Default mode. Control will still operate on default parameter settings.

CODE: E180.
RESULT: Outdoor air temperature sensor failure. Only shown if shorted or out of range (Communicating systems only).
FIX: Compare outdoor sensor resistance to temperature resistance chartsin unit installation instructions. Replace sensor pack if necessary. At beginning of (any) configuration, furnace or air handler control will sense outdoor air and discharge air temperature sensor(s) If detected (reading in range), appropriate feature will be set as installed and that could be seen in 'About' screen. In normal operation after control recognizes sensors, alarm will be sent if valid temperature reading is lost. To get rid of setting and alarm, redo configuration and make sure that temperature sensor is marked as not installed in indoor Unit 'About' screen. When indoor unit control is replaced thermostat will 'tell' new control if temperature sensor is in system or not. Clears 30 seconds after fault recovered.

CODE: E200.
RESULT: Hard Lock out - Rollout circuit open or previously open.
FIX: Correct cause of rollout trip or replace flame rollout switch. Test furnace operation. Cleared after fault recovered.

CODE: E201.
RESULT: Indoor blower/communication failure. Unable to communicate with blower motor.
FIX: Indoor blower communication failure including power outage. Lost communication with indoor blower motor. Possible causes: motor not powered, loose wiring. Problem may be on control or motor side. Cleared after fault recovered.

CODE: E202.
RESULT: Indoor blower motor mismatch - indoor motor horsepower does not match unit capacity.
FIX: Incorrect appliance capacity code selected. Check for proper configuring under Unit Size Code for Furnace/Air Hander on configuration guide or in installation instructions. Cleared after the correct match is detected following a reset. (Remove thermostat from system while applying power and reprogramming).

CODE: E203.
RESULT: Appliance capacity size is NOT programmed. Invalid unit codes. Refer to configuration flow chart.
FIX: No appliance capacity code selected. Check for proper configuring under Unit Size Codes for Furnace on configuration guide or in installation instruction. Critical Alert Cleared after valid unit code is read following a reset (remove thermostat from system while applying power and reprogramming).

CODE: E204.
RESULT: Gas valve mis-wired.
FIX: Check gas valve operation and wiring. Clears when repaired control.

CODE: E205.
RESULT: Gas valve control relay contact shorted.
FIX: Check wiring on control and gas valve. If wiring is correct replace control.

CODE: E206.
RESULT: Gas valve second stage relay failure.
FIX: Furnace will operate on 1st stage for remainder of the heating demand. Will clear after fault recovered. If unable to operate 2nd stage replace control.

CODE: E207.
RESULT: Hot surface igniter sensed open - Refer to troubleshooting.
FIX: Measure resistance of hot surface igniter. Replace if open or not within specified range found in 10M. Resumes normal operation after fault is cleared.

CODE: E223.
RESULT: Low pressure switch failed open.
FIX: Check pressure (inches W.C) of low pressure switch closing on heat call. Measure operating pressure (inches w.c.). Inspect vent and combustion air inducer for correct operation and restriction. Resumes normal operation after fault is cleared.

CODE: E224.
RESULT: Low pressure switch failed closed. Refer to troubleshooting.
FIX: Check pressure (inches W.C) of low pressure switch closing on heat call. Measure operating pressure (inches w.c.). Inspect vent and combustion air inducer for correct operation and restriction. Resumes normal operation after fault is cleared.

CODE: E225.
RESULT: High pressure switch failed open. Refer to troubleshooting.
FIX: Check pressure(inches W.C) of high pressure switch closing on heatcall. Measure operating pressure (inches w.c. Inspect vent and combustion air inducer for correct operation and restriction Resumes normal operation after fault is cleared.

CODE: E226.
RESULT: High pressure switch failed closed. Refer to troubleshooting.
FIX: Check operation of high pressure closing on heat call. Measure operating pressure (inches w.c.). Inspect vent and combustion air inducer for correct operation and restriction. Resumes normal operation after fault is cleared.


See What Our Customers Are Saying:

by Private User on Twintech Heating and Cooling

Our hot water tank died and with an after hours phone called Bob the sales guy jumped into action. Friendly, courteous and genuinely wanted to do whats best for our house hold we were given options and he awaited an answer with no pressure.

We decided on what we wanted and it was installed asap and Greg and team worked and cleaned up so well, you would never know there was a hot water tank there before!

We love our hot water tank and being able to have back to back to back showers without having to wait for the hot water tank to heat the water!

by Gary Grieves, Ajax on Twintech Heating and Cooling

I had heard of Twin Tech from a good friend of mine.
I needed to get a new Air Conditioner. It was not working properly and was 19 years old. I decided to get a new furnace at the same time.
I gave them a call on Saturday June 28.
I spoke to Bob Graham. I made arrangements for him to attend my house the following day.
I saw him on Sunday June 29 at 1100 AM.
He was on time and looked professional.
He spent 2 hours with me going over what I needed. He also suggested that I purchase a Humidifier. He gave me a quote of just under $11,000.00 for the purchase and installation of a Air Conditioner, Furnace and Humidifier. He was not pushy and gave me time to speak to my wife.
I called Bob on Monday June 30 and made arrangements to have it installed by the end of the week.
On Friday June 3 they arrived at 830 AM.
Again, right on time.
Greg and Mitch worked all day and finished the installation by 430 PM.
They made sure that everything was working properly and the basement was just as clean as it was before they came.
I will now be using Twin Tech to perform any maintenance needed on this equipment.
I was completely satisfied from start to finish with the service provided.

Thank You,
Gary Grieves.
Upchurch Ave.
Ajax.

by Kevin, Toronto on Twintech Heating and Cooling

We contacted TwinTech after having another ductless air-conditioning company come in to quote on a solution for our townhouse. We had a unique problem where my office was a hot spot - it's at the front of the unit and gets a lot of sun. If it's 20C outside, It's 29C in my office. The other company could not build a solution that would get a ductless unit to that room because of the location - the AC unit would have to be at the rear, and ductless systems would have to be on that side of the interior. TwinTech suggested a hybrid solution to fit our unique problem, where the ductless unit would move cold air to an air exchanger installed in our bedroom closet, and then they built a ducted vent system between all the upper rooms. This was less intrusive than building a central air system, and less expensive. Each room has a vent that I can close off, so I can push more cold air to my office when needed. We really didn't want ductless units sitting on the walls, and this looks and works better. I really appreciate the extra thought and care that went into the design of a solution, and the attention to detail in the installation. They answered all of our questions, and were able to do a bit extra by installing the ducts around the vents and painting them for us. It cost more than we originally planned for, due to our unique needs, but the fact that they offered financing helped us budget for more.
The job was done fast (I think we got lucky with timing where it wasn't the AC install busy season yet), and the team was very friendly and professional. They arrived and finished each day when they said they would. My office is now running at a comfortable temperature! I'm extremely happy with the experience and would whole heartedly recommend them.

by Private User on Twintech Heating and Cooling

How lucky are we to have this team come save us from our broken down, under sold, poorly installed previous unit (mind you there is a reason SEARS went bankrupt). Bob arrived on time to give us a detailed review of our unit and furnace; very knowledgeable. Greg arrived as planned with the new unit and reiterated what Bob explained how our furnace is equipped to handle the new unit and we didnt need to spend more money on a variable speed air conditioner. Cant say enough on how professional, efficient and personable this team is. Thank you so much guys!

by Private User on Twintech Heating and Cooling

We used Twintech for our replacement AC. Bob did a great job assessing what we needed and organized the install and showed up on install date. Greg and Mitch were on time and were very neat. They covered the traffic areas with a drop cloth and did an excellent install. Great clean up after install complete. Would recommend Twintech for heating and cooling.

by Private User on Twintech Heating and Cooling

They were fantastic, clean, freindly, great service. Would definitely recommend. Answered ally questions and more.

by Private User on Twintech Heating and Cooling

We woke up at about 7 a.m. the Sunday morning before Valentine's Day to a house that was barely 15 degrees Celsius on a really cold day. We tried to call some other suppliers but no answer or call back. We did a quick google search and Twintech came up. Had never dealt with them before. They had a chat line and lo & behold, someone answered; Greg. Helped us diagnose that our 40 year old furnace pilot light was out and walked us through how to relight it. All worked well; he even called me during this process. No charge I was told when asked.
15 minutes later, the pilot went out. It would not stay lit. Greg had Bob call us and we set up a meeting for about 11 a.m. that same Sunday.
Bob walked us through the options and even brought 3 electric space heaters for us to use. By Tuesday afternoon, we had a new Furnace and central air installed.

The team was helpful, responsive and respectful. Very glad we found them by accident and looking forward to a nice cool summer after a warm winter.

Thanks guys!

by Furnace And Humidifier Install on Twintech Heating and Cooling

Dealing with Bob and the installation crew was a pleasure. They took the time to explain everything. What would benefit us the most and the price difference. They were in and out in a reasonable time frame and fit us in within a couple days of original meeting. Quality of work is excellent as well.

by Private User on Twintech Heating and Cooling

A pleasure dealing with Bob ,Spencer and Mitch . They are professional and they also observe the covid 19 precautions . Bob explained the whole process and got the new furnace up the next day . Highly recommend

by Gary Monson, Ajax on Twintech Heating and Cooling

Would like to thank TwinTech for their quick response to our furnace repair. We used TwinTech to install a new furnace and AC a few years
back. Our furnace started to have problems early in the evening of extremely cold night. Contacted TwinTech and they were able make a service call later that evening. They got the furnace going and came the next day to replace a part. The part was under warranty and there was
no charge for either service call!
We are extremely happy with their customer service and would highly recommend them.
Gary & Kelly

See What Our Customers Are Saying:

by Aaron on Twintech Heating and Cooling

We are very happy to recommend this company to everyone. Our furnace broke down on Sunday morning. We phoned them and before noon Grant the owner showed up. He worked on the furnace for about a hour not wanting to give up to fix the problem. The furnace was 17 years old. I was the one talking about replacing it. End result was the next day it was all done. On the Sunday Bob came over with heaters to warm up the house. We decided to replace the water heater at the same time. Thanks Grant for the excellent work. Thumbs up.

by Linda on Twintech Heating and Cooling

Right on time. Explained how to work the HRV in a different way so the house would not be so dry. Changed my whole house water filter for me as well. Friendly, helpful, caring service!

by Robert Rogers on Twintech Heating and Cooling

Very pleased with the professional service that TwinTech Heating and Cooling provided in replacing my furnace. I got several quotes from different service providers. Their price was excellent and they explained the features very well. We are very glad we went with TwinTech and highly recommend their services.

by Robert Mizuno on Twintech Heating and Cooling

We were new homeowners in need of a second opinion. TwinTech Heating & Cooling were Amazing and professional. Very knowledgeable and great service all around. Recommend to anyone looking for honest and reliable services. Treated with respect and care. Thank you Greg, Mitch and Bob!

by Ruth on Twintech Heating and Cooling

TwinTech is an excellent and honest company! I called them for a second opinion after being told by another company that I needed to replace my furnace. Turns out this was not the case at all! I did not need a new furnace. TwinTech did not push to make an unnecessary sale and saved me from a huge expense. Bob and Mitch were extremely professional and above all honest! I definitely recommend TwinTech!

We Are Your Heat Pump Experts in Toronto

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - September 11, 2025

Toronto homeowners know how important it is to stay comfortable through hot summers and cold winters. That’s why more people are upgrading to heat pumps—a modern, energy-efficient solution that provides both heating and cooling in one

Read More

Will a Dent in My AC Effect Its Performance?

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - May 27, 2024

A dent in your air conditioning (AC) unit can potentially affect its performance, but the extent of the impact depends on several factors, including the location and severity of the dent. Here are some considerations: Location of the Dent:

Read More

Common Causes For An AC Breaking

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - April 19, 2024

Several common causes can lead to an air conditioner breaking down: Lack of maintenance: Regular maintenance, such as cleaning filters, coils, and checking refrigerant levels, is crucial for the proper functioning of an AC unit. Neglecting main

Read More

HVAC Repair and Replacement in Durham Region

  • SUBMITTED BY:
  • TWINTECH HEATING & COOLING
  • - March 29, 2025

When your HVAC system breaks down or isn’t performing efficiently, you need reliable service from a trusted local provider. Twintech Heating & Cooling is the Durham Region’s go-to expert for HVAC repair and replacement, offering to

Read More